Floor Heating EFH

Ensto floor heating cables are an economical, convenient and long-lasting way of heating your home. It is easy to install, easy to use and it does not leak or use too much energy. The floor feels pleasant and dries quickly. Tassu Floor Heating has obvious advantages in rooms with tiled floor but it can also be used to heat wooden floors. When there’s a limited possibility to raise the floor surface (e.g. when renovating facilities) Ensto’s TassuS is an excellent solution.

Tassu-floor heating cable

By using TASSU underfloor heating cables, a direct or partial storage floor heating can be carried out. The direct underfloor heating is used in wet or damp areas, where the floormaterial is low thermal resistant, e.g. clinker. The direct underfloor heating is suitable also in other areas as the only heating form. The partial storage underfloor heating is used for example in living rooms and kitchens. The output per square meter should be 80-150 W/m², the installation distance 15 – 25 cm and the installation depth 5-10 cm. The heating cable is a preterminated twin-conductor cable with a PVC sheath. The lowest installation temperature is -15°C. The output of the cable is 20W/m with a nominal voltage of 230V. The heating cable is supplied with a cold lead of 2.5 meter.
Tassu S -underfloor heating cables

The TASSU S underfloor heating cables are used in plasterboard floors, wooden floors and in renovation, where the cable is installed on top of the old floor. The output per square meter should be 70 – 100 W/m², the installation distance 9 – 20 cm and the installation depth 2.5 cm. The heating cable is a preterminated twin-conductor cable with a PVC sheath. The lowest installation temperature is -15 °C. The output of the cable is 10W/m with a nominal voltage of 230V. The heating cable is supplied with a cold lead of 2.5 meter.
ThinKit with thermostat

ThinKit is designed to be used as floor heating in small and cramped areas. The cable is round with a diameter of only 4.2 mm. The small diameter enables the use of less casting material during installation. ThinKit may be used together with a wide range of flooring material but the cable should always be laid upon fireproof material and have to be covered with levelling compound. The sizes of ThinKit cover an area of 1–20.6 m². ThinKit contains heating cable, a thermostat with Jussi and Elko compatible cover frames and center plates, flexible plastic tube and installation tape. The thermostat, ECO10FSJ+E, has an operating range of 10–35 °C. IP31. The length of the cold lead is 3 m.
ThinKit without thermostat

ThinKit is designed to be used as floor heating in small and cramped areas. The cable is round with a diameter of only 4.2 mm. The small diameter enables the use of less casting material during installation. ThinKit may be used together with a wide range of flooring material but the cable should always be laid upon fireproof material and have to be covered with levelling compound. The sizes of ThinKit cover an area of 1–20.6 m². ThinKit contains heating cable, flexible plastic tube and installation tape. The length of the cold lead is 3 m.
ThinMat-floor heating mat – 100 W/m² with thermostat

Lower power per square meter, 100 W/m², is sufficient for comfort heating in dry and damp indoor conditions. Wood, parquet, laminate, concrete, stone or clinker can be used for surface material. Suitable for installation on top of chipboard when floor heating coating is used. The package includes a floor heating mat, floor heating thermostat, adhesive aluminium tape, a sensor and a flexible installation tube for the sensor. The temperature range of the thermostat ECO10FSJ+E is 10 – 35 °C, IP31. The rated voltage is 230 V. Lowest installation temperature, + 5 °C. ThinMat width is 48 cm. The length of the cold lead is 4 m.
ThinMat-floor heating mat – 100 W/m² without thermostat

Lower power per square meter, 100 W/m², is sufficient for comfort heating in dry and damp indoor conditions. Wood, parquet, laminate, concrete, stone or clinker can be used for surface material. Suitable for installation on top of chipboard when floor heating coating is used. The package includes a floor heating mat, adhesive aluminium tape, and a flexible installation tube for the sensor. The rated voltage is 230 V. Lowest installation temperature, + 5 °C. ThinMat width is 48 cm. The length of the cold lead is 4 m.
ThinMat-floor heating mat – 160 W/m² without thermostat

More power, 160 W/m², is required in less insulated premises with concrete, stone or clinker flooring. Installation below wooden, parquet or laminate surfaces or on top of chipboards is not recommended. The package includes a floor heating mat, adhesive aluminium tape and a flexible installation tube for the sensor. The rated voltage is 230 V. Lowest installation temperature, + 5 °C. ThinMat width is 48 cm. The length of the cold lead is 4 m.
Ella-self-regulating underfloor heating cables

The ELLA cable elements made of self-regulating cable are only recommended for small spaces such as air locks and toilets. It is recommended to use a thermostat, either ECO10F or ECO10R, for regulating the heat. Nominal voltage 230V. Cold lead of 2.5 meter.
Fixing equipment

Cable fixing strip XBC1230 is used for fixing the underfloor heating cable.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>